Happy Wednesday! Here’s a gorgeous card that you might not have seen! Gail designed it for our Stamping 101 page—if you haven’t visited before, you should take a look. Stamping 101 features stamping basics, plus more advanced techniques, helpful hints, information on ink pads and of course, more projects!
Designer Tip: Stamping on acetate with Metallic StazOn® can be slippery, so use light pressure. I used a color printer to journal “Mom” on the back panel, but black would work fine, or you could write “Mom” with a burgundy colored marker.
- Pop-Up Box Die-Cut Cards
- Roses & Lace Double-Sided Paper Pack
- Roses & Lace Ribbon Set
- Lacy Things Stamp Set
- Heat Resistant Acetate
- Acrylic Block
- Gold Metallic StazOn® Ink Pad
- Scarlet SurfaceZ Ink Pad
- Zots™ Adhesive Dots
- Glue Stick
- Ultra Tape
- Fine Tip Black Pen or Computer Printer
- 1/8” hole punch
- Font: Snell Roundhand, 42 pt.
1. Card base: Cut six 2½”x2½” and one 2½”x5½” Roses & Lace green lace papers. Use Gold StazOn® to stamp the lace border centered at the bottom of three square pieces and the one long piece, then mat all of the pieces on the large pink rose paper with 1/8” borders. Follow the die-cut pop-up box instructions to assemble the box with Ultra Tape, but don’t install the inner supports yet. Close the box and lay flat on your work surface. Glue the stamped matted pieces onto the bottom panels with the long piece on the back panel (the one without an upper scored flap), then the remaining pieces onto the upper flaps (these will flop downward when the box is opened).
2. Card front: Open the box with the flaps down and the long panel at the back. Cut four 2 5/8”x2 5/8” pink lace papers. Journal “Mom” in burgundy on the center right side of one piece. Stamp the lace border in gold centered at the bottom of three pieces and at the top of the “Mom” piece, placing the scalloped edge on the edge of the paper. Cut 1/16” around the scalloped edge of the stamped lace, then mat all of the pieces on burgundy lace paper with 1/16” borders. Punch holes along the straight edge of the stamped lace, 1/8” from each side, and two holes centered at each scalloped valley, as shown. Lace with 1/8” ivory grosgrain, tying a bow at the center of two pieces. Glue the stamped matted pieces onto the three folded down panels and the “Mom” piece on the back panel, with the lace on the outer edge of each panel, and the bows on the center panels, as shown.
3. Supports: Stamp the lace border in gold centered at the top of two 2¾”x1½” green lace papers. Cut 1/16” around the scalloped edge of the stamped lace, then glue the strips even with the bottom of the two inner supports. Ultra Tape the two supports in place, as shown on the pop-up box instructions, close to the top open edge of the box (the lace edges extend above the opening.
4. TECHNIQUE: Shadow Stamping on Acetate: Stamp “Thinking of You” and “Wishing You a Beautiful Day” in gold on the heat resistant acetate, then stamp the same images over the first ones again with Scarlet SurfaceZ ink, offsetting the image up and to the right a bit for a shadow effect. Let dry, then cut out the sentiments and Zot™ onto the front and back panels, as shown. Use the same technique to stamp several small flowers, butterflies, hearts and scrolls. Cut out around the edge of each stamped image.
5. Zot™ ¼” wide strips from the acetate that comes with the pop-up box onto the backs of the pieces and Zot™ the other end of the strips onto the backs of the supports, arranging the pieces as shown. Zot™ on a scroll on the back panel and two tiny butterflies on the front and back panels.
This card is just stunning, and our Pop-Up Box Die-Cut Cards will deliver flawless results! I hope you’re feeling inspired and ready to do a little creating of your own! Thanks for stopping by. 🙂
Paper Wishes Blog